Differences

This shows you the differences between two versions of the page.

--- tools:s-tk:prefs [2019/08/08 14:54] – lightwolf
+++ tools:s-tk:prefs [2019/08/08 14:58] (current) – lightwolf
@@ Line 6: / Line 6: @@
 ===== Controls =====
-==== Evaluation Steps ====
-The number of cached values per span that are used to compute the orientation along the spline.
-If you find the orientation to be "jaggy", increase this value.
-==== Selected Steps ====
-This is used when the spline is selected and drawn into a viewport.
+==== Show Knots ====
+Displays a small circle at the position of the knots in the viewport.
-The value is number of lines drawn in the layout viewport per span to approximate the shape of the spline. The higher the value, the smoother the viewport representation is.
+==== Show Start/End Knots ====
-However, a larger value also takes longer to draw and uses a bit more memory.
+Displays a small circle at the position of the starting and ending knot of a spline in the viewport. This uses the colours defined below.
-==== Deselected Steps ====
+==== Start Colour ====
-This is used when the spline is not selected and drawn into a viewport.
+This is the colour used to draw the first knot in a spline (if Show Start/End Knots is enabled) and also to draw the main handle of the incoming control point of a knot.
+==== End Colour ====
+This is the colour used to draw the last knot in a spline (if Show Start/End Knots is enabled) and also to draw the main handle of the outgoing control point of a knot.
+==== Selected Spline / Deselected Spline ====
+The following settings are available for selected and deselected spline. This allows you to reduce clutter in the viewport for splines that aren't selected.
+=== Display Steps per Knot ===
+This is used when the spline is selected and drawn into a viewport.
 The value is number of lines drawn in the layout viewport per span to approximate the shape of the spline. The higher the value, the smoother the viewport representation is.
@@ Line 23: / Line 29: @@
 This value can be quite low if you have many splines in your scene and the ones you don't have selected don't have to be as precise.
-==== Selected Width ====
+=== Line Width ===
 The width of the lines used to draw a selected spline in the viewports in pixels.
-==== Deselected Width ====
+=== Display Alignment ===
-The width of the lines used to draw a deselected spline in the viewports in pixels.
-==== Show Knots ====
-Displays a small circle at the position of the knots in the viewport.
-==== Show Start/End Knots ====
+This shows the orientation along the spline as well as the influence of the up vector.
-Displays a small circle at the position of the starting and ending knot of a spline in the viewport. This uses the colours defined below.
-==== Show Normals ====
-This shows the orientation along the spline as well as the influence of the twist angle.
   * **None** Doesn't show any normals.
-  * **All** Shows the normals for every Evaluation Step.
+  * **Every Step** Shows the normals for every Evaluation Step.
   * **Knots Only** Only shows the normals at the knots.
+  * **Ribbon** Doesn't show the normals but displays the spline as a ribbon.
-==== Start Colour ====
-This is the colour used to draw the first knot in a spline (if Show Start/End Knots is enabled) and also to draw the main handle of the incoming control point of a knot.
-==== End Colour ====
-This is the colour used to draw the last knot in a spline (if Show Start/End Knots is enabled) and also to draw the main handle of the outgoing control point of a knot.